QPL CERTIFICATION for PM907S & PM948S SERIES OF FILM CAPACITORS
Exxelia is pleased to announced the ESA/QPL certification for its film capacitors series PM907S and PM948S.
Series PM907S and PM948S of Film capacitors obtained the QPL certification from the European Space Components Coordination (ESCC). According to the ESCC Detail Specification No. 3006/025 and 3006/026 QPL certified products ensure superior performances, quality and reliability intended for use by the European Space Agency (ESA) and in Space in general.
PM907S and PM948S are full series of Polyester Film Capacitors. PM907S products are suitable for voltages from 50V up to 1250V and offer capacitance values from 82nF up to 180μF. PM948S can be used with a voltages from 50V up to 630V with capacitance values from 22nF up to 47μF. Both series can support extreme conditions with temperatures from -55°C to +125°C, and offer high energy density, low ESR & ESL and high RMS current.
Products are typically being used in SMPS (Switch Mode Power Suppliers) and BUS filtering.
These two certified series complete the list of Exxelia Group’s QPL certified film capacitors, that now includes:
– PM96S (T)
Introduction of DSCC 93026 qualified Wet Tantalum Capacitors
Exxelia’s range of wet tantalum capacitors WT84 is now fully qualified to DSCC 93026 drawing for voltages from 25V up to 125V. Available in all case sizes (T1, T2, T3, T4) the family is housed in a hermetically sealed tantalum case and is designed to withstand the most stringent environmental constraints. Thanks to the continuous improvements conducted in the manufacturing processes combined with the high purity tantalum powder used by Exxelia, DSCC 93026 provides the highest capacitance per unit volume. In addition, compared to conventional wet tantalum capacitors, DSCC 93026 features much lower ESR and higher ripple current. DSCC 93026 is qualified for capacitance values range from 10µF up to 1800µF at voltages from 25V up to 125V, and with operating temperatures of -55°C to 125°C. The series is ideal for use in high-reliability defense, avionics, radars and power supply applications requiring high capacitance or high energy storage. DSCC 93026 is available now for order.
Exxelia at Space Tech Expo – Booth #5009
100% invar tuning screws with self-locking system Invar-36 is a unique Iron-Nickel alloy (64 % Fe / 36 % Ni) sought-after for its very low coefficient of thermal expansion. With 1.1 ppm. K–1 between 0°C and 100°C, Invar-36 is about 17 times more stable than Brass which is the most traditional and common alloy Tuning Elements are made of. The working temperature range in Space is so wide that this property becomes essential for a reliable and stable cavity filter tuning. Self-locking system is a technology commonly used on Tuning Element made of Brass or other soft “easy-to-machine” alloys but is innovative and pretty advanced when applied to hard and tough Invar 36. The design consists of two threaded segments separated by two parallel slots. After cutting both parallel slots, the rotor is compressed in its length in order to create a plastic deformation. Thus, an offset is induced between the two threaded segments which generates a constant tensile stress in the rotor from the moment threaded segments are screwed. High power and high frequency ceramics with the new C48X dielectric Range of high voltage ceramic capacitors based on brand new dielectric material C48X, combining most advantages of NPO and X7R dielectrics. Compared to X7R material, C48X dielectric allows to get the same capacitance values under working voltage with the unrivaled advantage of a very low dissipation factor (less than 5.10–4). Besides, it can also withstand very high dV/dt, up to 10kV/μs, which makes it the solution of choice for pulse and fast charge/discharge applications or firing units. Thus capacitors with C48X dielectric appear to be ideally suited for power applications where heat dissipation may be detrimental to performances and reliability. Magnetic components based on adaptive CCM technology Exxelia designed CCM technology to respond to the growing interest of electronic engineers for inductors and transformers with multiple outputs, high power density and reduced footprint. Qualified for aeronautic and space applications, the CCM product line features terrific robustness. The CCM technology adapts to most every need, even the harshest environments, including VIGON® resistance. The series offers five different sizes, allowing optimized component design in a pick-and-place surface mount (SMD) package. Through-hole (TH) packages are also available upon request. CCM transformers and inductors can operate over a wide temperature range with a minimal temperature of -55° C. The standard thermal grade of the technology is 140° C. The epoxy molding protecting the winding ensures a lower temperature gradient and a better heat dissipation. Each unit is thoroughly tested with a dielectric withstanding strength of 1,500 VAC.